Soldering & Torches

The PUK 6 arc welder with the SM6 microscope offers precise, repeatable welds on precious metals with WIG impulse welding. Its 0.2mm spot size allows for intricate tasks like welding near gemstones. With up to 3.3 welding spots per second, low operating costs, and a three-year warranty, it's reliable and cost-effective. The touchscreen interface and 11 memory slots streamline operation, while features like the smoothing function improve welding on materials like silver, copper, and bronze. The SM6 microscope provides 10X magnification, adjustable lighting, and ergonomic design for precise work. Set Includes • PUK 6 welding device • SM 6 welding microscope • PUK flow regulator • Handpiece • 3m gas hose • Contact clamp • 0.6mm electrodes

Designed for jewelry repair and manufacture, for hobby, for crafts and for metal sculpture and supplied in a display box. The Little Torch™ is engineered for light brazing and soldering. Produces a perfectly controlled, stable flame hot enough to melt metals, glass and ceramics with thread-thin flames. The propane temperature can go up to 4780° F (2637°C). The kit includes: 8' (182cm) hose the Little Torch™ 5 curved tips #3-7

Hose for soldering torches 12 feet. Dual hose: Red for propane and Green for oxygene. Diameter: 3/16" Length: 12' (aprox. 3.65 meters)

A device that primarily controls the flow direction of fuel or oxygen. Helps prevent dangerous reverse gas flow. It is strongly recommended for increased safety. These check valves should be installed between the regulator and the hose. Both have 9/16” connections.

Propane; Oxygen; These UL listed regulators are used to allow high-pressure tanks to be reduced and to regulate to safe and usable pressures for torches.

The Y connectors allows you to operate with multiple torch use from a single tank and regulator. Available for Gas/Fuel and Oxygen, with on-off valves or without valve.

Electronic torch lighter. Uses 2 AA batteries (not included). Easy to use.

Heavy duty diagonal cutter for cutting sprues with minimal effort. The grips shape allows to have better control. Available with straight or curved blades. Regular scissors handles. Overall length is 7½”, and cutting capacity is 3mm. Made in Germany.

Most commonly used on the soldering block. Honeycomb blocks have fine pores to accelerate the heat loss from parts being soldered. Holes may be used to hold pins to keep work in place while heating. Asbestos free. These blocks withstand temperatures up to 2000°F/1093°C and the round honeycomb up to 6000°F (3315°C). Small Rectangular: 3¾” X 5½” X ½” Large Rectangular: 5½” X 7¾” X ½” Round: 4½” Diameter X 1” Thickness

Ceramic tapered 6'' rod on a heavy base to suit all ring sizes. Mounted on base, swivels to provide the exact position or angle desired.

Facilitates soldering freeing both hands. Cross-Lock tweezer is included.

VIGOR® HEAT-SHIELD protects any surfaces from flame damages or heat transfer during soldering and brazing procedures (precious stones, previously soldered joints, enameling, etc.) It is a non-toxic, non-corrosive and oderless paste. Protects heat up to 5000°F (2760°C). Prevents oxidation and cleans away easily with water.

pack of 3

It is a very durable and powerful general purpose flux that protects your parts during soldering. It is an active fluoride-type flux which is appropriate for soldering gold, silver, brass and all nonferrous metals. It can be cleaned up with hot water.

Slightly higher temperature bearing lead free solder, melts at 450°F (230°C). May be used with a soldering gun or a torch. Use StayClean flux to achieve a good flow characteristics. Kit includes ½ oz. of solder and ½ fl oz. of Stay Clean flux.

Made from selected soft wood. Easy to pin or press work pieces while soldering. Under the flame the charcoal glows and reflects heat back on the article being soldered. Size 5½” X 2¾” X 1-1/8”

The Magnesia Block is porous and fireproof. Lasts longer than charcoal blocks. Soft enough to enable work to be pressed into the surface and steadied while soldering. Withstands temperatures up to 2000°F (1093°C). Measures 6" x 3" x 1½".

Can be placed over alcohol lamp so that work can be heated from below while soldering or enameling. Mesh screen is 6"x 6" (included) Available in 2 sizes.

Red for propane and Green for oxygen. Comes will all connectors to replace the hoses for the Little Torch™. Each hose is 8' long.

This torch holder mounts anywhere on a bench. It can hold any type of soldering torch.

A metal weighted base with storage for tips and a magnetic mount to securely hold the Little Torch. (Torch and tips are not included)

This kit is for the "REFILLABLE" oxygen and propane tanks. Kit includes: ♦ Little Torch kit ♦ Oxygen Regulator ♦ Propane Regulator ♦ Oxygen Check Valve ♦ Propane Check Valve * we also sell the refillable oxygen tank but it can't be shipped

An economical answer to your soldering needs. Works without bottled oxygen. No oxygen or air supply needed. Simply draws from the air that surrounds us. Offers flame versatility with its three interchangeable tips: Tip #1 (Small) up to 2000°F (1200°C) • Tip #2 (Medium) up to 2300°F (1250°C) Tip #3 (Large) up to 2400°F (1300°C). Includes also a regulator for the disposable propane tank and the hose. Made in Brazil.

Used after welding, consisting of granular acid for the cleaning and removal of the oxidation of silver, gold, copper and most other non-ferrous metals.

For making jewellery soldering flux. Allows solder to flow. Can be used to put on melting crucibles that will protect it from wering it fast.

Picklers provide a safe and effective method for removing oxides or fire scale from the surfaces of precious metals. Used with pickling salt and water.

Annealing Pan rotates 360º with easy access. The heat reflecting pumice is perfect for supporting your project in any position - flat or embedded. This pan comes with an attachable third hand custom designed to fit with our pans. Pan measures 7 inches and includes pumice. Made in USA.